# Inside Ride Kickr E-Flex Trainer Motion System

**URL:** <https://www.trainerroad.com/forum/t/inside-ride-kickr-e-flex-trainer-motion-system/20469>\
**Category:** Equipment\
**Tags:** trainer\
**Created:** [September 3, 2019, 7:05pm UTC](https://www.trainerroad.com/forum/t/inside-ride-kickr-e-flex-trainer-motion-system/20469 "2019-09-03T19:05:25Z")\
**Posts on this page:** 1\
**Showing post:** 210

<div class="post-metadata">

**Author:** ![mcneese.chad](https://sea2.discourse-cdn.com/trainerroad/forum/user_avatar/www.trainerroad.com/mcneese.chad/32/15056_2.png) [@mcneese.chad](https://www.trainerroad.com/forum/u/mcneese.chad)\
**Post date:** [February 27, 2020, 8:07pm UTC](https://www.trainerroad.com/forum/t/inside-ride-kickr-e-flex-trainer-motion-system/20469/210 "2020-02-27T20:07:35Z")

</div>

TL;DR… Crazy long post as my review to follow (_who’s surprised I got a little wordy_ 😛 ).

- Short answer is that I like it in the stock form, but it’s much more to my liking after reducing the leveling and centering forces.
- Overall, I am very happy with the E-Flex. It gives a basic feel close to my other rockers, with some differences in force input and directions.
- I plan to do some more testing to see if I can get it even closer to what I see as the best solution possible.

* * *

**E-Flex Initial Impressions:**

- The shipping package was small and light when delivered. It almost seems like the E-Flex couldn’t all be in there, but it is.
- The two bases are well protected in the packaging. Once removed from the box, the two bases are light and small. This leads to the E-Flex being easy to move around for setup.
- The E-Flex looks very clean with a professional build quality. It has the look and feel of a premium product, and is worth the price from that perspective.
- One small issue, when testing the Fore-Aft motion by hand, I heard some squeaks. Turned out that two of the o-rings were rubbing against the sides of the slots at the mounting points to the outer tubes.
  - The tubes are deburred well, and won’t likely lead to wear on the o-rings, but the noise was something I wanted to eliminate. I added a small piece of Gorilla tape to the sides of all slots, and that silenced the Fore-Aft motion.

**Instructions:**

- They are lacking detail in certain areas.
  - Use of the different leaf spring setting is not clear and lacks specific instruction about removing screws, and then swapping the part orientation.

- The order of operations could be improved for more linear flow.
  - The leaf spring info comes after installing the Kickr on the rear section. It should be first, before any install steps.

- There is no mention of the steering/lean lock knob on the front section. This should be covered and explained.
  - Despite the oversight on the steering lock, there is coverage of the rear tilt lock, that is used for shipping. This is most likely because it needs to be “unlocked” for final use.

- Per the instructions, you position the middle leg of the Kickr a measured distance from the front clamp. This works alright, but I wonder if there is an easier way that doesn’t require the person to measure.
  - Perhaps the rear of the Kickr could be positioned flush with the leaf spring as a landmark, and still hit the same position without the need to measure?

- The instructions show the front support and clamp positioned ahead of the fork.
  - I notice that Ray Maker installed his 180\* from that, with the steering lock at the rear of the fork. This makes sense to me and puts the lock within reach while on the bike (at least for me and my bike size and arm reach).
  - I wonder if this “backwards” installation should be the default position shown by Inside Ride?

**Setup:**

- Aside from the instruction notes above, The installation and setup are relatively easy.
- I love the finished look. It takes up a very small footprint compared to even my smallest rocker plates.
- I also love the low stack height. The E-Flex sets the bike at roughly the same height as it is with regular wheels. This makes mounting and dismounting very easy. It doesn’t require stepping onto a platform like most rocker plates (that often raise the bike 3-5” higher).

**First Ride, and Use Discussion:**

- Rocking Movement (Left-Right Pivot):

- Fore-Aft Movement (Front-Back Translation):

- I took notes on the feelings for motions in both directions and started to form a plan for making changes and retesting.

**My Modifications:**

- Fore-Aft Centering Spring Force:
  - I wanted to reduce the force and after reviewing the assemblies, I decided the front was the right place to start.
  - I completely disconnected the front Fore-Aft Centering Springs, from the middle connection on the slider. I just shifted the slider, pulled the o-ring off the mount washer & spacer under the slider, and slid it to the edge of the frame, so it would not contact the center slider.
  - Now, all of my F-A centering forces are controlled by the rear section o-rings.

- Steering-Leveling Spring Force:
  - I wanted to reduce the force, but also the progressive nature of the Steering-Leveing Springs. After review, I decided adding length between the middle o-ring mount and shifting it closer to the pivot axis would drop the spring force, and flatten the leverage rate a bit.
  - I added some S-hooks to the mount washer & spacer under the steering lock. These moved the connection point roughly 1” closer to the pivot to reduce leverage, and shorten the effective eye-to-eye length of the contact point about 1” as well (totally estimating these values from memory, and can document better distances and pics to show the changes later).

**Second Ride:**

- Leveling Spring Force:
  - I do a test where I push the saddle fully right, and watch to see how it rebounds and how long it takes to stop rocking. With my rockers, it takes a minimal force (guessing 15-20 lbs side force pushing the saddle) and it rocks back and forth for quite a while before stopping.
  - The original setting on the E-Flex shows higher force and much shorter rocking time in the test above.
  - Repeating the test after the change to the o-ring connection and leverage rate were just what I wanted. The leveling force is much lower, and less progressive in the travel. It allows the bike to wobble back and forth much more like my other rockers

- Rocking Input:
  - It makes the rider have more control to keep the bike balanced since the leveling springs are providing less support, which is what I want. I can still ride seated upright, with no hands on the wheel to eat, drink, blow my nose, and anything else I do on my other rockers.
  - It also makes the standing effort and steering input much lower force. The motion angle is still interesting, but the force is much better for my taste. It is a more realistic effort to get the rocking vs the very still default setting.
  - It is all much smoother in and out of the saddle, with a clean feel that is what I want.
  - Fore-Aft Motion:
  - Cutting the f-a centering force roughly in half made a huge difference. The return forces are more gradual, without the “snap” that seemed to get me out of phase during the initial test.
  - The forces are much closer to what I tested before, and I have no complaints with the single setup of springs.

- Overall, the changes I made get this almost right for my needs.

**Comparisons to Other Rockers and Outside:**

- Now that the turning the handlebars for rocking is easier, the amount of input is more notable to me. The handlebar turn movement seems excessive for a steer to lean angle (ratio) compared to lean and turn outside. I will call the E-Flex a 1:1 ratio (but that is totally made up and not analyzed). The issue I have with the E-Flex is that it takes lots of handlebar steering angle input to get what I like for a roughly 5\* lean angle while standing.
- As mentioned above, riding outside leads us to add some steering while rocking. I suspect the steering is roughly half of what we see on the E-Flex when it comes to comparing steering input vs actual rocking angle from pushing the handlebars up/down.
- That leads the E-Flex to feel a bit off to me when doing the standing efforts since the direction and amount of motion is not quite like what I think happens outside. I plan to try and capture the lean angle to steering angle to rocking angle inputs/outputs, to put some numbers to my theories. But I think we will find that a mix of steering and pure leaning take place.

**Wish List:**

- Before I get to things I’d like to see changed, I want to say that with the modifications above, the price I paid and the results from the 2nd ride (as well as a few more since then) lead me to be happy with my purchase of the E-Flex.
- At stock build, I suspect it will meet the needs of most riders. They have an amazing platform that achieves the main goal of adding motion in two directions. It is done with professional build quality and feel.
- The main point I would like to see changed is the ability to make adjustments to spring forces.
  - I think alternate attachment points for the springs, to allow at least 3 different settings would be beneficial. I know not everyone will want what I like, but I think there is room to have something like mine, the current setting from IR and something in between. Ideally, a more finite adjustment would allow very custom tuning, but could be more complex than is necessary or cost effective. Adding a few attachment points to reduce the o-ring stretch are a relatively simple option, but not the only one.

- The next point I would like to see changed, but need to experiment with to learn what I really want is the inputs for rocking action.
  - I think the steering direction as the only input for rocking is lacking for the E-Flex.
  - I also think the pure up-down direction as the only input for regular rockers is also lacking.
  - Ultimately, I think a blend of steering input (E-Flex) and tilting input at the bars (regular rocker) will be a feeling that more closely mimics outside riding.
  - I plan to make a test with the E-Flex by modding the base to allow around 3\* of rocking on its own. It will be spring leveled and half the travel of my other rockers. My hope is to have this “regular rocker” part as the main activation for the seated rocking.
  - Then it will also assist while standing, and allow for less steering action to get a fuller range of lean. No idea how it will work, but I think this is one of those instances where both sides have it right, and also a bit wrong. A hybrid of the two controls and motions may well be the right mix.

* * *

**New info about my fulcrum mods:**

I completed the initial testing on the stock E-Flex. Then I started modding I covered the “normal” mods with spring force adjustments in the long post linked above.

- [Pics and other info on my mods](https://www.trainerroad.com/forum/t/inside-ride-kickr-e-flex-trainer-motion-system/20469/222).

I have been testing another mod for weeks and pretty happy with the results, but have more to play with to fine tune performance.

Effectively, I closed the open C-shape of the front base, by adding a 1" x 2" board across the rear section. Then I added a piece of PVC tube directly under the middle of the front and rear supports. This elevated the base a bit, and created a fulcrum where the entire E-Flex front section pivots left to right (roll axis rotation). Finally, I added my original foam springs under the outer parts of the rear bar, to act as leveling springs for the new pivot motion. This change offers about 3\* of lean with no steering input from the E-Flex.

This allows the entire front section to pivot left and right, like our existing rockers. I call these “plain” rockers, since they tilt left and right by pure force input on the left and right of the rocker. As noted, the E-Flex uses steering input at the bars to cause tilting. So I have created a hybrid rocker that includes pure balance with steering input. It comes much closer to matching the input/output that I feel when riding outside.

1. Seated, I can lightly rock the bike left and right with not steering input. That requirement to still have steering input for small rocking (less than 3\* lean) seem odd to me and doesn’t match what I feel outside. So my mod allows non-steering rocking with simple left-right balance inputs at the bars and saddle.

2. Standing, I can combine the steering input from the E-Flex along with the shorter travel rocking from the new fulcrum. It feels way better for me to reach the normal 5-6\* lean that I use when standing. It no longer forces me to turn the bars super far with what feels like way more turning than I apply outside. I get a nice mix of the steer and pure lean force control and like the result overall. I still need to play with spring rates and total travel allowed with each control direction.

I will note that this setup gets even closer to what I experience riding my motion rollers. I can still ride seated, upright with no hands, but it takes way more focus and early attention to balance to keep from flopping over. It is a result of my reduced E-Flex steering springs, and my relatively low force on the fulcrum leveling springs.

I freely admit that my setup right now is likely at the very fringe of rockers. I suspect most people would hop on and flail around and not feel right. I plan to throw some friends on just to see.

Point being, I am continuing my silly search for the “perfect” rocker and am likely well outside what is needed or even wanted by most people.

The E-Flex in stock form is one of the best rockers I have ever ridden. At it’s price, and if you own a Kickr, I think it may well be the best purchase to be had.

---

_[View the full topic](https://www.trainerroad.com/forum/t/inside-ride-kickr-e-flex-trainer-motion-system/20469)._
