# Help Required - abismal ERG mode

**URL:** <https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473>\
**Category:** TrainerRoad Software\
**Created:** [January 9, 2019, 2:35pm UTC](https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473 "2019-01-09T14:35:45Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![kevistraining](https://sea2.discourse-cdn.com/trainerroad/forum/user_avatar/www.trainerroad.com/kevistraining/32/171237_2.png) [@kevistraining](https://www.trainerroad.com/forum/u/kevistraining)\
**Post date:** [January 9, 2019, 2:35pm UTC](https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473/1 "2019-01-09T14:35:45Z")

</div>

Sorry for the repeat post but thought I might get a little extra visibility with a new thread…

Had an absolute nightmare with powermatch ERG mode yesterday.

Setup is Assioma DUO with Tacx Vortex smart trainer over ANT+ to Win10 PC

 ![powermatch%20pain](https://global.discourse-cdn.com/trainerroad/original/2X/2/24ae2ba9ff84aa15ee68d7ccca057887981366ca.jpeg)

It’s like its not even trying! What hurts the most is it not slackening off the resistance after the intervals.

Power readings measured from both devices not too far off when viewed in the “devices” screen but did notice that the power from the assiomas lag behind the vortex by around 4 seconds.

Any advice on a way to improve things? If i turn powernatch off can I still have power recorded from the pedals with the vortex adjusting resistance? I’d rather it be stable at a slightly incorrect setpoint than what happened above.

Also do you think it would be any better using bluetooth instead of ant? For the last too intervals I switched to my phone and connected via bluetooth and it seemed a bit better - i was able to maintain a roughly consistent cadence but then the signal to my pedals dropped out because my phones bluetooth antenna is so poor…

Awesome that you can switch device and resume a workout by the way - totally didn’t expect to be able to do that!!!

---

<div class="post-metadata">

**Author:** ![pwandoff](https://avatars.discourse-cdn.com/v4/letter/p/bb73d2/32.png) [@pwandoff](https://www.trainerroad.com/forum/u/pwandoff)\
**Post date:** [January 9, 2019, 2:56pm UTC](https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473/2 "2019-01-09T14:56:51Z")

</div>

Here’s a bunch of links to threads that you may find helpful; there’s a bunch more if you search for ‘ERG’ in the search feature

> [@Which gear with ERG](https://www.trainerroad.com/forumt/which-gear-with-erg/9390/21):
>
> see highlighted. It looks like @Crownan was correct, but BKool doesn’t specify what “minimum speed” is. Perhaps someone else can find it. Obviously shifting down will help to a point so I guess my advice would be, use whatever gearing works with the minimum power you use because it should also work for the upper end as well.

> [@Tacx Neo not in ERG-mode](https://www.trainerroad.com/forumt/tacx-neo-not-in-erg-mode/6750):
>
> Hello everyone, I have just connected my new Tacx Neo but can’t seem to get it to accept ERG-mode. Am i missing something??. Regards DrJ

> [@ERG Mode and Tacx Flux S, Power2Max, controlling with lower wattage](https://www.trainerroad.com/forumt/erg-mode-and-tacx-flux-s-power2max-controlling-with-lower-wattage/8012):
>
> Hello! I am using the following equipment: TACX Flux S, Power2Max Powermeter Win 10-Laptop with an Ant±Dongle and an USB extension-cable (Dongle is placed right next to the trainer). Most of the workouts I am doing with the smaller ring in front (34) and about 23-25-27-30 at the back. I have the following issue: During a SST-Training the software seems to have a problem, when the wattage is dropping from, for example, 190 watt (sst-intervall) to a cool-down-part with about 85 watt. The watt…

> [@ERG mode fluctuations](https://www.trainerroad.com/forumt/erg-mode-fluctuations/4697):
>
> Elite Direto user here. I feel that the power readings from my intervals fluctuate very much, check out the image below: Is this similar to other users on here? I try to focus on keeping a steady cadence and always run the bike in the small chainring and middle of the cassette. Feel free to post screenshots of your readings and also what smart trainer you are running slight_smile

---

<div class="post-metadata">

**Author:** ![Supermurph19](https://sea2.discourse-cdn.com/trainerroad/forum/user_avatar/www.trainerroad.com/supermurph19/32/3304_2.png) [@Supermurph19](https://www.trainerroad.com/forum/u/Supermurph19)\
**Post date:** [January 9, 2019, 3:05pm UTC](https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473/3 "2019-01-09T15:05:30Z")

</div>

If you’ve got a power meter just ditch ERG mode in my opinion. You don’t need it, you’ll learn to judge things a lot better by self regulating. (RANT OVER).

---

<div class="post-metadata">

**Author:** ![berto2cj](https://sea2.discourse-cdn.com/trainerroad/forum/user_avatar/www.trainerroad.com/berto2cj/32/4413_2.png) [@berto2cj](https://www.trainerroad.com/forum/u/berto2cj)\
**Post date:** [January 9, 2019, 3:17pm UTC](https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473/4 "2019-01-09T15:17:33Z")

</div>

Easiest solution is above. Drop one from the equation and roll with it. You could use pm and non-erg or just your trainer for pm and continue to use erg.

Actually trying the latter alone could rule out the trainer as the issue.

Second thing to chase down is firmware on both items. I have a tacx vortex and it didn’t work right until I updated firmware.

Third - dig through those threads and start checking off the tips one by one.

---

<div class="post-metadata">

**Author:** ![Tezz](https://sea2.discourse-cdn.com/trainerroad/forum/user_avatar/www.trainerroad.com/tezz/32/24009_2.png) [@Tezz](https://www.trainerroad.com/forum/u/Tezz)\
**Post date:** [January 9, 2019, 3:35pm UTC](https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473/5 "2019-01-09T15:35:09Z")

</div>

When I have power match enabled I can’t stand Erg mode. When I disable power match I love Erg mode. Except I wanted so bad to use my power meter for indoors and outdoors for consistency. I asked TR to look at my files and they saw some interference, so I did a test with all other electronics turned off and nothing changed. Then it was brought up that having a single sided meter makes power match even more tricky. So in the end after a bunch of spin downs on my Kickr Core to get the Kickr to read very close to my PM I’m trying Erg mode enabled and power match disabled. I monitor my intervals on my Garmin reading my PM and if they are a little off I just adjust intensity to get as close as possible. I did notice the warmer my trainer gets it’s within a few watts now. I did slightly manipulate my spin down just a touch until I was happy. Probably not recommended…

---

<div class="post-metadata">

**Author:** ![kevistraining](https://sea2.discourse-cdn.com/trainerroad/forum/user_avatar/www.trainerroad.com/kevistraining/32/171237_2.png) [@kevistraining](https://www.trainerroad.com/forum/u/kevistraining)\
**Post date:** [January 9, 2019, 3:35pm UTC](https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473/6 "2019-01-09T15:35:16Z")

</div>

Cheers 👍

Good idea regarding trying just the trainer and seeing if it’s any better - love a good experiment.

I’m not really keen on ditching ERG mode, I like it and it worked ok on that other program that I’ve just cancelled my zubscription for…

I’m wondering weather I just had a really flaky ant+ connection to my trainer. I’ll go trainer only and see if it’s any better - I can always record my assioma power using my head unit to see if it’s much different to the numbers the vortex spits out.

---

<div class="post-metadata">

**Author:** ![didierbr](https://avatars.discourse-cdn.com/v4/letter/d/76d3ee/32.png) [@didierbr](https://www.trainerroad.com/forum/u/didierbr)\
**Post date:** [September 8, 2019, 8:52pm UTC](https://www.trainerroad.com/forum/t/help-required-abismal-erg-mode/9473/7 "2019-09-08T20:52:58Z")

</div>

One of the thing with ERG mode on vortex is you have to change gears. To high and a reasonnable Cadence will push you over the watts you are looking for. You have the same problem with too low a gear you might not be able to do the required watts.
