Erg mode slow to react - Tacx Neo, Ebbetts Workout

Hi Chad! I saw the same thing happening with my Neo on today’s ride during Spanish Needle.

Check the link for my activity. Hopefully you can see it.

I also log my workouts with my Edge so I’m guessing this is not a Bluetooth issue since it’s connected via ANT+ to my Edge. Link below for the activity on Strava:

https://www.strava.com/activities/2104077861

1 Like

Your TR account is private, so I can’t access the info.

You should be able.to see it now.

1 Like

Your workout looks great to me. That has all the basic work applied and you will get all of get training benefit, IMHO.

1 Like

@mcneese.chad please take a look: https://www.trainerroad.com/career/doublepinchflatuws/rides/48948484-ebbetts

as u can see, i hit the peak power numbers as per target but if u zoom in you’ll see it was very laggy during the sprints…


After reviewing nearly every sprint in your workout, well zoomed in, I see a max of 2 seconds offset from the green instruction change to the point the yellow power meets or exceeds the blue target.

Importantly, the yellow actual power line is only 1 second offset from the blue target. I just don’t see that as “very laggy”. It seems reasonably quick to me.

As I see in my intervals, you are getting the full benefit of time at or above the power target. I don’t see a problem here. We are looking at a very narrow window of time.

If you want better control, you may be best to swap to Resistance mode to have full control of the process.

1 Like

I actually noticed the same thing, in Erg mode on my Neo, the short (less than 15) seconds or so it lags too much.

Here is my last run on Ebbetts from a few weeks ago. Didn’t seem to have any issues on my Tacx Neo. To achieve the power in the short 5-10sec sprints I have to be in the big ring. What chainring are you guys using?

1 Like

I did Ebbetts today too on Tacx neo in erg mode and also experienced it hard to Average the desired Watts in 5 sec. I was able to hit the wattage just not “average” it in such a short span of time. I’m always in the small ring on the front and middle of the cassette. I feel like I got the benefit of the workout even though the numbers don’t look perfect. My workout is below:

1 Like

Both of the workouts above also look good to me. You can see different approaches in the gearing, cadence and jump timing. But they each are getting the power profile really close to the target, IMHO.

I’m riding my KTM hardtail, Eagle MTB.
So 34 up front 1x and the 5th up from the bottom on the Shimano 11 speed 10-28 cassette on my Neo.
Chainline perfectly straight, ERG MODE so no shifting. It’s the one gear in the cassette that is perfectly lined up with one of the shifting Eagle indexes.

So I’m not generating as much flywheel rpm as you guys in the big road rings. But my cadence is always 92 and up.

2 Likes

I did Ebbetts a few weeks ago and I too have a Tacx Neo. It’s hard to get those 5 seconds, but I just went for it, from the start and didn’t follow the graph on the screen or anything. I just gave it all I could.

This is from one of the sprints in the very last interval. It’s not perfect, of course, but I am satisfied with the trainer.

1 Like

Again, that looks great. I think you got it figured out and are getting what is intended.

My interpretation is that people often get confused by the (not matching target) numbers shown on screen after a shorter interval or in the interval summary.

With smooth pedaling and small front ring I usually get close to those short interval targets with the Neo if I look them up on the web page, zoom in and shift those 5, 10 or 15 second block 1-2 seconds to the right. So not 1:00-1:10 but 1:02-1:12 for example.

There is a feature request to do that automatically and look some seconds around for each short interval and use the part with the highest average power for that interval duration and show that in the interval summary list. You might want to comment and upvote here:

1 Like

Thanks for taking the time to look into it @mcneese.chad!

1 Like

@chadmcneese here’s my file for ebbetts today. I’m on a vortex. I’m not sure I get the intended benefit. Managed to get 3-4 seconds of work a above prescribed on virtually every burst interval. But my trainer is so slow to ramp down on some of them it took over 20 seconds to get back to the sweetspot I was supposed to be in. All in all every single interval was in the treshold range for average power.

1 Like

Looks perfectly acceptable to me.

image

I focus on the “area” of the power zone and even if it is shifted to the right (like we see here), you are quite close to having a block with the same area.

The key point to keep in mind is that these efforts are more about a pure effort and load. The fact that it doesn’t perfectly follow the defined block is OK, really… it’s OK :stuck_out_tongue:

3 Likes

Thanks a lot.

1 Like

I think Chad you are completely correct, the training exposes the user to the required training level, but as a Neo owner, I can tell u it’s really frustrating, you build yourself up for 150%, 3,2 1 … nothing,nothing, spin spin, pedal to fast, oh here we go, other times when you think, wait a couple of seconds … don’t spin, brick wall

It might have the desired training, from a user experiance it’s a bit rubbish, why do a count down, if you’re actually going to do it a few seconds later

1 Like

I guess you may be having a different experience than me. There are two things in play here:

  1. What do we feel and experience in the moment of the workout.

    • TR sends the actual resistance change instruction in ERG at about 2 seconds to go (this might even vary from trainer to trainer as loaded in the TR app, but I’ve seen mixed info on that). I know on my Neo, Kickr and H2, that I get “hit” with power from jumps like this before the actual 0 in the countdown.
    • This is done in part to offset the actual power captured and try to align it better with the prescribed blocks when doing analysis in #2 below. It doesn’t always work for alignment, but for me, it usually means I am well into the power kick when I am officially in the power block.
    • What you are describing seems to be different from my experience, and I’m not sure why that would be?
  2. What do we see in the post workout analysis.

    • As above, the TR app sends the resistance change early, hoping to get closer matches between planned and actual power.
    • This can be impacted by the rider’s power/cadence reaction to the resistance change, the actual trainer used (delay and response capabilities), the gearing used on the trainer (some respond faster in different gearing), and who knows what else? As such, we can see different results despite apparently similar use.
    • I have played a fair bit and come to one basic trick for these jumps. I often drop my cadence 5-10 rpm prior to the jump. Doing this causes the resistance brake to clamp down a bit more from the slower cadence. When the interval hits, I accelerate my cadence back to or well beyond the prior cadence. Doing so means I hit a harder resistance and higher power level sooner than purely waiting on the trainer to make the change. It doesn’t always work, but it’s something that I find works most of the time.
5 Likes